Opticis HDWX-100-TR Transmitter/Receiver Wireless KVM & HDMI Extender OPTI-HDWX-100-TR

Wireless Extender, the Opticis HDWX-100-TR is designed for wireless signals extending of HDMI, keyboard and mouse. The transmitter module HDWX-100-T connected to the HDMI source encodes the HDMI by H.264 and transmits the signal via advanced Wi-Fi, 802.11a/n technology. The receiver module, HDWX-100-R connected to the display receives and decodes wireless signal into HDMI for display.

The USB keyboard and mouse interface in the receiver module, HDWX-100-R also can be accessed to the source via transmitter module HDWX-100-T, if it is connected to the source by USB interface.

The HDWX-100-TR supports the digital video data of full HD up to 1920x1080p at 60Hz and 7.1ch surround audio and transmits the signal up to 30 meters (100feet). It also enables to distribute one (1) video source up to four (4) displays and makes four (4) local keyboard and mouse accesses to the source.

By using GUI interface, user can select one of active transmitters for pairing in the receiver side. With these key features, 4 x 4 wireless routing system can be configured without any electrical connection.

Applications:
Home AV
KVM
Video control room
Digital signage
Medical imaging

Note: The HDWX-100-TR has a reverse voltage protection circuit and the receiver (Rx) module also has overcurrent protection circuit. The HDWX-100-TR is designed to use mainly external +5V AC/DC power adaptor. The internal power supplied through a HDMI pin is used to identify normal connection between a source and transmitter, HDWX-100-T.

Features:

• Compact design for direct hook up
• Wi-Fi standard: 802.11n, 5GHz, 2x2 MIMO, two internal antennas
• Maximum throughput: 300Mbps
• WPA/WPA2 and QoS
• Video resolution: Up to 1920x1080 at 60Hz
• Audio: 7.1ch surround
• HDMI V1.3 and HDCP2.0
• DVI V1.0 backward compatibility
• USB backchannel: extend PC control in remote-site (RX): HID mouse and keyboard
• Provides LED indicators for Power and Status (wireless connection) in Transmitter and Receiver
• Size (WDH): 66 x 105 x 25mm

Specifications:

• Wi-Fi
• Wi-Fi standard: 802.11n, 5GHz, 2T2R MIMO
• Security: WPA/WPA2
• QoS: 802.11e QoS WMM/WMM-PS
• Band: 5GHz
• Mode: 40MHz
• Frequency: 5.17~5.835GHz
• Tx Power: Typical 13dBm at 5GHz(TBD)
• Coverage distance(In case of 1:1 connection): LOS (Line of Sight): Up to 80mters, NLOS: Up to 30meters (Typically 20meters, Indoor)
• Maximum throughput: Up to 300Mbps
• Antenna: Two internal antennas
  
  Transmitter Only
• Compression (Encoding): H.264/MPEG4 AVC(part 10)
• Video Input: HDMI Rx 1.3
• Operation WPS: PBC and PIN
  
  Receiver Only
• Compression (Decoding): H.264/MPEG4 AVC(part 10)
• Video output: HDMI Tx 1.3, DVI 1.0 backward compatibility
• Operation: Connection manager (GUI), EDID
  
  CODEC
• Resolution: Up to 1080p (1920 x1080), 60Hz
• Video format: RGB 4:4:4, YCbCr4:4:4, YCbCr4:2:2
• Audio format: 4 x I2S, 7.1ch surround audio
• HDCP: HDCP2.0
• Video latency: CODEC: Sub 1msec
  
  Supporting Resolutions
• 480p60, 576p50
• 720p50, 720p60
• 1080i30, 1080i50, 1080i60
• 1080p24, 1080p30, 1080p50, 1080p60
• 640x480p60
• 800x600p60
• 1024x768p60
• 1280x768p60
• 1280x960p60
• 1280x1024p60
• 1600x1200p60
• 1920x1080p60
  
• Note: Some DVI resolutions may not be shown properly on the display. The image would be shifted to one side.
  
  General
• Multi-cast: 1 transmitter to 4 receivers distribution at 1080p, 60Hz
• Connectivity: P2P (Peer to Peer) with Wi-Fi Direct 5GHz
• P2P connection: Wi-Fi Protected Setup(WPS): PBC and PIN
• Input/Output: interface HDMI Tx/Rx (Audio/Video), USB for FW Upgrading
• USB KVM extender: USB Mouse & Keyboard on the remo